Beam Penetration Works and installation of strengthening plates
J&I have successfully completed the forming of 30no Beam penetrations varying in size from 400mm diameter to 900mm wide x 250mm high. J&I...
LATEST NEWS
Forming 13m x 2.7m Staircase Opening
J&I have successfully completed the forming of a 13m long by 2.7m wide staircase opening on the 10th floor of Exchange House. J&I...
9 views0 comments
Construction of Service Trenches
J&I have successfully completed the forming of new slabs and service trenches at an engine testing facility. The existing slab was broken...
17 views0 comments
Forming Door Openings in RC Walls
J&I have successfully completed the forming of 5no door ways through RC walls. By using a combination of stitch drilling, Track Sawing...
108 views0 comments
Demolition of RC Staircase and installation of Timber Floor Infils
J&I have successfully completed the demolition removal of four flights and two landings of an RC staircase using Track Sawing and Brokk...
83 views0 comments
Stitch Drilling to form new Riser
J&I have successfully completed the precise cutting of a slab by means of stitch drilling to form a new riser shaft. This was completed...
5 views0 comments
Cutting of structural columns to allow Acoustic bearing installation
J&I have successfully completed the precise cutting of structural columns to allow acoustic bearings to be installed. Higher demands on...
87 views0 comments
Structural Steelwork to support Structural Glazing & Cladding at London South Bank University
J&I have successfully completed the Design, fabrication and installation of circa 60 tonnes of structural steelwork to the main elevation...
40 views0 comments
Removal of Steel & Glass Staircase and Lightweight Structural infill of the opening
J&I have successfully completed the following works within a live building to remove an existing steel and glass staircase inc all...
32 views0 comments
Steel Frames installed to support existing RC building
Here on a project we have installed Structural Steel Frames to support existing RC beams on a commercial to residential conversion...
12 views0 comments
Stitch drilling
When a section of concrete needs careful removal and access it too tight for a saw, a series of overlapping holes are cored. These cores...
13 views0 comments
Saw cutting through RC to form doorway
On this project we cut a new door opening through a RC wall in a basement for access to a plant room. The building was completed and live...
16 views0 comments
Forming services openings and rebuilding brickwork walls
Our buildersworks teams have been forming new services penetrations through masonry walls and rebuilding tops of existing walls at our...
8 views0 comments
Installation of Structural Steelwork Goal Post
We have successfully cut out a section of RC structure using our Hilti Hi-frequency track saw and installed a steel framed 'goal post' to...
25 views0 comments
Installation of Structural Steelwork Beams
We have successfully installed some very large beams to support the underside of an RC structure. These beams were 6m long and weighed...
11 views0 comments
Forming Pile Caps Project
We have successfully completed the stitch drilling, track sawing and removal of concrete to form pile caps within a basement ready for a...
29 views0 comments
New advert for Total Construction magazine
We have placed an advert along side one of our clients in Total Construction Magazine which hopefully has an outreach of over 100k readers!
57 views0 comments
Forming Opening for staircase installation
On this project we have cut and formed openings for new staircase openings through the 1st floor slabs.
49 views0 comments
Lift Shaft Extension from 14 levels to 15 levels with over-run
On this project we have demolished the top of an existing shaft whilst the building is live. We used a method of sawing and hand...
70 views0 comments
New Livery for Company Vehicles
We have renewed our fleet of vehicles to comply with the latest ULEZ guidelines and also applied new signwriting!
23 views0 comments